new year new car gta v6 gt

A place to showcase your pride and joy

Moderators: eastlmark, BIG_MVS, Test Moderator

User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Sun Feb 27, 2011 12:34 pm

Just a little blemish and on the mains anyway .
Bottom end ,de-glaze liners and pop on heads and we're done for the most part on the lump .
Image
Image
Image
Image
no avatar
User

andy001

Rank

Non Member

Posts

972

Joined

Sat Jul 18, 2009 6:09 pm


Has thanked: 1 time
Been thanked: 3 times

Postby andy001 » Sun Feb 27, 2011 1:09 pm

Oooo....looking good when do you think it will be time for the grand start up :D
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Sun Feb 27, 2011 1:35 pm

Depends on bits arriving and stupid carbs :wink: .I've not bothered to look at them too closely yet but there's lots of little pipes that need replacing :evil:
Grinder is aimed at that subframe bolt next ,the heat from that should get it shifted :evil:
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Thu Mar 31, 2011 2:03 pm

Been a bit sidetracked with JIL but about ready to fire up .Bolt on subframe did come out eventually after a months soak and a big hammer .

Before ..
ImageImage
After..
ImageImage

Hopefully it won't sound like a jackhammer now 8)
no avatar
User

andy001

Rank

Non Member

Posts

972

Joined

Sat Jul 18, 2009 6:09 pm


Has thanked: 1 time
Been thanked: 3 times

Postby andy001 » Thu Mar 31, 2011 4:16 pm

looking good :D
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Thu Mar 31, 2011 8:28 pm

We'll get there mate ,chief ,boss ,chap ,marrow .....

Should all be back in and ready to fire up early next week .Might need to bodge a few pipes on the carbs but just want to get it running for MOT purposes then I can bed it in 8)
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Wed Apr 06, 2011 3:53 pm

In the car ...some pics of ze carb orrible ...Not that bad actually .Only bit dodgy was the ali ' valve ' on the choke .

ImageImage
ImageImage
ImageImage
Image
ImageImage
Image
Last edited by clee on Thu Apr 07, 2011 7:39 am, edited 1 time in total.
no avatar
User

andy001

Rank

Non Member

Posts

972

Joined

Sat Jul 18, 2009 6:09 pm


Has thanked: 1 time
Been thanked: 3 times

Postby andy001 » Wed Apr 06, 2011 7:38 pm

thats a hell of a lot of bolts and bits, im truly impressed,great work lee :D
no avatar
User

eastlmark

Rank

Non Member

Posts

2197

Joined

Sun Jul 09, 2006 3:50 pm

Location

East London


Has thanked: 55 times
Been thanked: 48 times

Postby eastlmark » Wed Apr 06, 2011 10:07 pm

this reminds me of something being served up for school dinners.
Image
User avatar
User

JohnC

Rank

Non Member

Posts

2120

Joined

Sun Dec 02, 2007 6:19 pm

Location

Jersey C.I.


Has thanked: 15 times
Been thanked: 83 times

Postby JohnC » Wed Apr 06, 2011 10:31 pm

clee wrote:Only bit dodgy was the ali ' valve ' on the choke .

It appears from your pic that the alloy pipe attachment has rotted away on the old one....Two questions, where did you get the "new" one from, and.... is there enough meat in the housing of the old one to tap and fit a brass pipe connection like the one on the other side of the unit in order to repair it?.
1990 GTA Atmo, 2003 Jaguar X type 2.5SE Auto, 2018 Kia Picanto GT-Line-S 1.25
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Thu Apr 07, 2011 7:34 am

New one is an old one from another setup .
Probably enough meat to tap it ,wall section is thick enough but I think that would reduce the bore too much as it's only about 6mm and you'd lose 2/3mm of that with the new pipe .Probably out of solid on that side as opposed to brass fitting as the valve unit is very close .
Only real solution is to ali weld a new bit on .
User avatar
User

JohnC

Rank

Non Member

Posts

2120

Joined

Sun Dec 02, 2007 6:19 pm

Location

Jersey C.I.


Has thanked: 15 times
Been thanked: 83 times

Postby JohnC » Thu Apr 07, 2011 9:33 am

Thanks for that Lee.....I had the same problem on mine, but it was only badly corroded but was the cause of my loosing coolant. This does appear to be another common fault (another one :roll: ...surely not). I do know of a number of these that have failed. It does appear that the corrosion starts after a number of years due to the deteration of the hose which causes the coolant to weep through and when it meets the air, pitting occures which eats away around its junction with the main body. Mine had not corroded through fortunately, so I was able to clean it right down to the alloy and with two pack epoxy build it up back to original plus a bit keeping the original profile. I then slipped a length of adesive heat shrink over it right up to where the vacuum valve sits...applied a hot air gun, and now the coolant goes no where near the external alloy. It has only been on for a few months now and around 300 miles covered, I took off the hose to check a week ago, and it all appears OK.
Pic shows repaired unit prior to the heat shrink being applied.

Image
1990 GTA Atmo, 2003 Jaguar X type 2.5SE Auto, 2018 Kia Picanto GT-Line-S 1.25
User avatar
User

si21

Rank

Non Member

Posts

2094

Joined

Mon May 09, 2005 8:24 pm

Location

S.E London


Has thanked: 3 times
Been thanked: 2 times

Why Mark

Postby si21 » Thu Apr 07, 2011 12:58 pm

eastlmark wrote:this reminds me of something being served up for school dinners.
Image


Did you attend a young offenders institute :?: :lol: :lol: :lol:

Si21
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Fri Apr 08, 2011 4:44 pm

nearly ...out again for to make a few adjustments to slave pipe work ...might have to rob some bits off the grey hatmo .No problem as it was just nestling in anyway .back in tomorrow ....Claude keeping a beady on it :wink:
I'm getting very superstitious in my old age :lol:
Image
Image
no avatar
User

andy001

Rank

Non Member

Posts

972

Joined

Sat Jul 18, 2009 6:09 pm


Has thanked: 1 time
Been thanked: 3 times

Postby andy001 » Mon Apr 25, 2011 10:15 pm

how's it going lee,is it a runner :D
PreviousNext


  • Advertisement

Who is online

Users browsing this forum: Baidu [Spider] and 22 guests

Powered by phpBB ® | Renault' and 'Alpine' are trademarks of Renault S.A.S. or its subsidiaries and are used with kind permission of Renault France